If your business has been temporarily closed due to the Coronavirus containment; you have probably been eagerly awaiting the day you can reopen and welcome back your staff and customers!

As you make plans to reopen, whenever that might be, take a moment to safely plan and successfully power your espresso machine back on after closure.

These steps are best taken by a trained technician – if you need any help (or a recommendation on a local tech), please reach out to us at dispatch@espressotime.com  or 972-690-6969

Before You Open:

*Plan on performing this startup process several days to a week in advance of your opening to have plenty of time to deal with anything unexpected.*

When you call your technician to schedule this appointment, consider incorporating a PM (preventative maintenance) procedure into the visit to keep your machine running in tip-top shape. A technician is the best person to restart your machine, as they can ensure a safe and thorough reactivation.

We also recommend contacting your water filtration supplier or service provider for instructions about proper flushing of filtration equipment. These devices can require attention after sitting dormant for a while. While you’re at it, this is a great time to change your cartridge and/or conduct a water test if you haven’t done so recently.

Before you get started, thoroughly sanitize and disinfect all your equipment with appropriate agents.

Step 1: Verify Drain Connection

Ensure the drain tray and drain box of the machine are clean and free of debris.

Ensure the drain hose is securely attached to the drain box, routed at sufficient slope to floor drain, and secured in place.

Step 2: Verify Water Supply

The following steps are written assuming boilers have not been drained. If boilers have been drained, your best move will be to work with a service technician. Contact Espresso RMI LLC Solutions for instruction on bleeding groups and initial filling procedure.

  • If water supply valve is not already shut off, do so now.
  • Remove supply hose at pump inlet, turn water supply valve back on, and flush water line into a 5 gallon bucket for a duration of two minutes. Bucket should be nearly full unless filtration system isn’t able to put out the required 2 gallons per minute to the machine pump.
  • Turn water supply off, reattach supply hose at pump inlet, and turn water supply valve back on.
     For additional building water systems information see guidance from the CDC.

Step 3: Verify Electrical Supply

  • Verify machine mains power is in OFF position and machine is unplugged.
  • Verify circuit breaker has been turned on.
  • Verify machine cable is now plugged securely into electrical receptacle.

Step 4: Turning the Machine On

  • Turn machine on. You may or may not hear valves open or the pump activate, depending on the level of water in the steam boiler. (If machine has a position 1, do not proceed to position 2 until you have verified the boilers contain water. Group valves can be activated in position 1 to confirm water in coffee boiler. For machines with a sight glass, they should rest at approximate ¾ full position for machines, ½ for steam systems.)
  • If machine has not sufficiently filled within five minutes, turn off and contact a service technician.
  • Turn to position 2, if applicable, and machine will begin to heat.
  • Remain near machine to monitor.
  • Machine will be at operating temperature and pressure within 15-20 minutes.
  • Steam gauge operational position will be between 1.25 and 1.5, 1.75 on steam systems.
  • Coffee boiler gauge should not exceed 12 bar.
  • Test proper operation of all groups and valves. Inspect for leaks.
  • Refresh steam boiler via discharge cycle or by purging several cycles of tea spout.
  • Run groups for approximately two minutes. Open steam valves for approximately two minutes.
  • Clean and backflush machine as per nightly maintenance routine.
  • Check flow rate for each group by measuring the output (without a porta filter) for 30 seconds to ensure they are similar. If there is a large variation between groups, you should consult your technician.

That’s it!

You’re ready to resume service. Our Solutions team is here for you if any questions come up along the way or if anything seems amiss. Call us at 972-690-6969.

Again, the best way to start your machine up after a closure is to bring it in to your service provider Espresso RMI LLC Solutions.

Comments

  1. Thank you for the auspicious writeup It in fact was a amusement account it Look advanced to more added agreeable from you By the way how could we communicate

  2. Its like you read my mind You appear to know a lot about this like you wrote the book in it or something I think that you could do with some pics to drive the message home a little bit but instead of that this is fantastic blog An excellent read I will certainly be back

  3. Somebody essentially lend a hand to make significantly posts I might state That is the very first time I frequented your web page and up to now I surprised with the research you made to create this particular put up amazing Excellent job

Leave a Reply

Your email address will not be published. Required fields are marked *